Simultaneous Analysis of Quality, Inventory and Maintenance Costs by Considering Rework in Single-Machine Production System

Document Type : Research Paper

Authors

1 Associate Professor, Department of Industrial Engineering and Management, Shahrood University of technology, Shahrood, Iran.

2 Professor, Department of Industrial Engineering, Faculty of Engineering, Alzahra University, Tehran, Iran.

Abstract

Equipment failure leads to non-conforming products and there is usually a direct relation between the failure rates and the amount of the non-conforming products. Inventory is another issue for production managers and so, they should provide an optimum condition between these related issues. This paper aims to investigate the policies of maintenance, quality control, and inventory in a single machine production system simultaneously with the aim of minimizing total costs. To close the problem to practical condition, machine failures are considered under uncertainty with a known distribution probability. The maintenance time is assumed dependent on the maximum non-conforming products produced per unit and the amount of buffer stock. Moreover, the non-conforming products can be reworked in an additional work station. The problem is formulated and modeled under different various scenarios considering three kinds of cost including quality control, inventory, and maintenance. To test the proposed model, four scenarios are investigated for a numerical example consists of: production period without shortage, production period with compensable shortage, production period before the buffer stock with compensable shortage, and time-based cost analysis. Finally, result analysis has been presented that demonstrates proper efficiency of the proposed model in cost reduction.

Keywords

Main Subjects

References

  1. Cheng, G.Q., B.H. Zhou, and L. Li, Integrated production, quality control and condition-based maintenance for imperfect production systems. Reliability Engineering & System Safety, 2018. 175: p. 251-264.
  2. Colledani, M. and T. Tolio, Integrated quality, production logistics and maintenance analysis of multi-stage asynchronous manufacturing systems with degrading machines. CIRP annals, 2012. 61(1): p. 455-458.
  3. Sana, S.S., Preventive maintenance and optimal buffer inventory for products sold with warranty in an imperfect production system. International Journal of Production Research, 2012. 50(23): p. 6763-6774.
  4. Cassady, C.R., et al., Combining preventive maintenance and statistical process control: a preliminary investigation. Iie Transactions, 2000. 32(6): p. 471-478.
  5. Rahimi Kakehjoob, P., Farughi, H., & Rasay, H. (2024). Joint production and maintenance optimization for a single-machine deteriorating system in a finite planning horizon. Journal of Industrial Engineering and Management Studies, 11(2), 53-69.
  6. Linderman, K., K.E. McKone-Sweet, and J.C. Anderson, An integrated systems approach to process control and maintenance. European Journal of Operational Research, 2005. 164(2): p. 324-340.
  7. Wang, S. and M. Liu, A branch and bound algorithm for single-machine production scheduling integrated with preventive maintenance planning. International Journal of Production Research, 2013. 51(3): p. 847-868.
  8. Wang, W.-Y., Optimum production and inspection modeling with minimal repair and rework considerations. Applied Mathematical Modelling, 2013. 37(4): p. 1618-1626.
  9. Budai, G., R. Dekker, and R.P. Nicolai, Maintenance and production: a review of planning models, in Complex system maintenance handbook. 2008, Springer. p. 321-344.
  10. Liao, G.-L., Y.H. Chen, and S.-H. Sheu, Optimal economic production quantity policy for imperfect process with imperfect repair and maintenance. European Journal of Operational Research, 2009. 195 (2): p. 348-357.
  11. Kang, K. and V. Subramaniam, Integrated control policy of production and preventive maintenance for a deteriorating manufacturing system. Computers & Industrial Engineering, 2018. 118: p. 266-277.
  12. Kuo, Y. and Z.A. Chang, Integrated production scheduling and preventive maintenance planning for a single machine under a cumulative damage failure process. Naval Research Logistics (NRL), 2007. 54(6): p. 602-614.
  13. Bouslah, B., A. Gharbi, and R. Pellerin, Integrated production, sampling quality control and maintenance of deteriorating production systems with AOQL constraint. Omega, 2016. 61: p. 110-126.
  14. Aghdam, S. S., Fattahi, P., Hosseini, S. M. H., Babaeimorad, S., & Sana, S. S. (2023). Joint optimisation of the maintenance and buffer stock policies considering back orders. International Journal of Systems Science: Operations & Logistics, 10(1), 2169054.
  15. Lin, Y.-H., J.-M. Chen, and Y.-C. Chen, The impact of inspection errors, imperfect maintenance and minimal repairs on an imperfect production system. Mathematical and Computer Modelling, 2011. 53(9-10): p. 1680-1691.
  16. Gitinavard, M., Fattahi, P., & Babaei, M. (2022). Using a P Control Chart for Joint Optimization of Maintenance, Quality, and Buffer Stock Policies in Single Machine Production Systems. International Journal of Industrial Engineering & Production Research, 33 (4), 1-23. ‎
  17. Chen, J.-M., Y.-H. Lin, and Y.-C. Chen, Economic optimisation for an imperfect production system with rework and scrap rate. International Journal of Industrial and Systems Engineering, 2010. 6(1): p. 92-109.
  18. Chen, Y.-C., Optimal production and inspection strategy with inspection time and reworking for a deteriorating process. International Journal of Operations Research, 2013. 10(3): p. 123-133.
  19. Tambe, P. P., & Kulkarni, M. S. (2022). A reliability based integrated model of maintenance planning with quality control and production decision for improving operational performance. Reliability engineering & system safety, 226, 108681.
  20. Pinciroli, L., Baraldi, P., & Zio, E. (2023). Maintenance optimization in industry 4.0. Reliability Engineering & System Safety, 234, 109204.
  21. Shi, L., Lv, X., He, Y., & He, Z. (2024). Optimising production, maintenance, and quality control for imperfect manufacturing systems considering timely replenishment. International Journal of Production Research, 62(10), 3504-3525.
  22. Tasias, K. A. (2024). Simultaneous optimization of inventory, maintenance, and quality for production systems subject to multiple mean and variance shifts. Communications in Statistics-Theory and Methods, 53(9), 3078-3101.
  23. Rezg, N., S. Dellagi, and A. Khatad, Joint Optimization of Maintenance and Production Policies. 2014: John Wiley & Sons.
  24. Rezg, N., Dellagi, S., & Chelbi, A. (2008). Joint optimal inventory control and preventive maintenance policy. International Journal of Production Research, 46(19), 5349-5365.
Advances in Industrial Engineering
Volume 59, Issue 1
June 2025
Pages 183-197

Files

Share

How to cite

Statistics